Note:
1. This is the DIY version that comes unassembled.
2. Comes without battery, charger, receiver or remote control.
Item | Specification |
140mm Racing Frame Kit | Wheel base: 140mm Frame arm thickness: 3mm Upper plate thickness: 1mm Side plate thickness: 1mm Frame kit material: 3K carbon fiber & CNC 6065 aluminium |
1607 2800KV 2-4S Brushless Motor | KV: 2800KV Lipo cell: 2-4S Weight: 17.8g (includes wires) Output shaft length: 14mm Maximum pull: signal 630g (4S 3030 4-blade propeller) Maximum power: 350W Configu-ration: 9N/12P Mounting holes distance: 12*12mm Mounting holes: φM2 Bearing: NSK N52 Strong NdFeB Magnet Recommend propeller: 3 inch |
4 IN 1 20A BLHeli_S ESC | Continuous current: 20A Pe ak current: 25A (10S) BEC output: no Input voltage: 2-4S Main control chip: 48mhz EFM8BB2 Firmware upgrade: Supports Dshot600/BLHeli_S/Oneshot125 MOS: 3*3 MOS type: vs3610ae 30v64a |
Customized F4 Flight Controller | Main control chip: STM32F411 Sensor: ICM20602 6-axis Integrated OSD PPM/DSM/IBUS/UAR share: UART1-RX Mounting holes distance: 20*20mm Weight: 24g PID circulation rate and refresh rate can up to 32kHz Supports Betaflight/cleanflight/inav firmware |
700TVL CMOS Camera | Case size: 19mm*19mm Weight: 9.5g Total pixels: PAL: 1020H×596V (0.61MP); NTSC: 1020H×508V (0.52MP) Effective pixels: PAL: 976H×582V (0.57MP); NTSC: 976H×494V (0.48MP) Signal system: PAL/NTSC switchable Resolution ratio(horizontal center): 700TVL Video output: 1.0Vp-p/75Ω Automatic gain control: 0.25/0.50/0.75/1.00, up to 55dB White balance: off Exposure mode: electron exposure Electronic shutter: 1/50(1/60) – 1/100000 S Gamma correction: 0.45/1.0 Synchronization method: inter-sync Camera lens: standard 2.1mm Lens operating voltage: DC 5-12V Working current: 70mA (low power consumption) Working temperature: -20℃~-60℃ Humidity: 0%~98% |
5.8G 40CH 0mW/25mw/200mw switchable VTX | Supports TBS SmartAudio Transmitting power: 0mW/25mW/100mW/200mW switchable Channel: 40CH Full video format: NTSC/PAL Input voltage: 7V~24V Power dissipation: +12V/600MW Size: 25×20×6mm Weight: ≤3.2g (except antenna) With copper pipe mini antenna (ipex antenna) Make sure the antenna is installed at the output end before powering up to avoid damaging internal components. |
3030 4-blade propeller | Material: PC Mounting hole: 5mm Center thickness: 6mm Quantity: 10 pairs Color: black, red, yellow, green Weight: 5g a pair Delivery color randomly (10 pairs of propellers are the same color) |
Lipo Battery | Not included Recommend 2-3S 450-650mah |
Package included:
1 x 140mm racing frame kit
2 x 1607 2800KV brushless motor CW
2 x 1607 2800KV brushless motor CCW
1 x 4 IN 1 20A BLHeli_S ESC
1 x Customized F4 flight controller
1 x 700TVL CMOS camera
1 x 5.8G 40CH 0mw/25mw/200mw switchable VTX
2x 3030 4-blade propeller CW
2 x 3030 4-blade propeller CCW
Return:
If item DOA(Dead of Arrival),Buyers Can return it in 14 Days,We will Replace it with New item after we receive DOA item.Please Contact us Before you sent the item back
Warranty:
All item Comes with Basic 3 Month Sellers Warranty,if item defective in 3 Month,We will offer replacement withour extra Charger(including shipping fee)After we Receive the Defective item.
If item Defective after 3 Month,Buyers can still send it back,We will contact suppliers or Manufactory for Warranty.Buyers Might Need pay the Shipping fee For resend the replaced item.
Be the first to review “Eachine Tyro79 140mm 3 Inch DIY Version FPV Racing”